Koch-Chemie Ceramic Body Cb0.01 Ceramic Coating
Koch-Chemie Ceramic Body Cb0.01 is a professional ceramic coating designed to provide long-lasting paint protection, outstanding gloss, strong hydrophobic performance and enhanced resistance to environmental contamination.
Size: 30mL
Key Benefits
- Provides long-lasting ceramic paint protection
- Enhances gloss and paint depth
- Creates strong hydrophobic performance
- Helps protect against environmental contamination
- Suitable for professionally prepared automotive paintwork
- Approximate consumption: 15–30mL depending on vehicle size
Surface Preparation
Proper surface preparation helps Ceramic Body Cb0.01 bond correctly to the paint and achieve the best possible finish.
- First, thoroughly pre-clean or wash the vehicle with an alkaline cleaner. For example, use Green Star diluted 1:10. Do not use sealing shampoos before polishing and coating.
- Next, remove heavy contamination such as tree resin, rust film or tar. Use Reinigungsknete rot or blau, Teerwäsche A or a similar suitable product where required.
- Then, inspect the condition of the paintwork. For heavily to moderately weathered paint, mechanically polish the surface with Heavy Cut or Fine Cut. Refer to the relevant product information for the correct polishing process.
- For slightly weathered paintwork, use Micro Cut high-gloss polish with an eccentric polisher. This step also helps remove holograms left after Heavy Cut or Fine Cut polishing.
- After polishing, remove all polish residue completely with a clean Polish and Sealing Towel.
- Next, wipe the surface gently with a clean Polish and Sealing Towel soaked with Silicon- & Wachsentferner or Panel Preparation Spray. Immediately wipe the surface again with a fresh Polish and Sealing Towel before it dries.
This preparation process removes surfactants, drying aids and polishing oils that could interfere with the adhesion of Ceramic Body Cb0.01.
Important: For sensitive uni or single-layer paint, dilute Silicon- & Wachsentferner with water at a ratio of 1:4. Preferably use distilled water to help prevent matting or surface damage.
Finally, inspect the paintwork under proper lighting. The surface should appear free from scratches and holograms. After this step, avoid touching the paint with bare fingers or palms because skin oils may cause adhesion problems. Wear suitable gloves during the coating process.
How to Apply Ceramic Body Cb0.01
- First, apply a sufficient amount of Ceramic Body Cb0.01 to an Application Sponge. Alternatively, use an Applikatorblock together with an Application Towel.
- Next, work panel by panel and spread the coating quickly and evenly across the paintwork.
- Then, apply two cross coats. Make sure you can see a thin, closed film of liquid across the treated area.
- After that, allow Ceramic Body Cb0.01 to flash. Temperature and humidity determine the required flash time.
- Next, remove excess product with a Coating Towel.
- Use a fresh side of the towel and buff the surface gently in circular movements without applying pressure.
- Finally, inspect the paint under proper lighting and check carefully for high spots or remaining coating residue.
Flash Time
Higher temperature and humidity shorten the flash time.
Application example: At approximately 20°C / 68°F and 43% humidity, allow around 6 minutes of flash time.
Approximate consumption: 15–30mL depending on vehicle size.
Double-Layer Application
If you apply two coating layers, allow approximately 30 minutes of drying time after the first coat. Temperature and humidity may change the required drying time.
Curing Time
- Allow at least 24 hours for the coating to become weatherproof.
- Do not wash the vehicle for at least 9 days.
- Temperatures below 15°C / 59°F extend the curing time.
- During the first 9 days, gently remove bird droppings and insects as soon as possible.
In addition, you can apply Spray Sealant S0.02 or Hand Wax W0.01 after 24 hours to help protect the ceramic coating while it continues to cure.
Recommended Maintenance
We recommend hand washing to maintain the high-gloss ceramic surface for as long as possible.
- For alkaline cleaning, use Green Star diluted 1:10.
- For neutral maintenance washes, use Gentle Snow Foam.
- For mineral contamination, use Reactivation Shampoo for deeper cleaning.
After washing, use Hydro Foam Sealant S0.03 diluted 1:50–1:200 as a wet sealant.
Alternatively, use Spray Sealant S0.02 as a maintenance topper.
Professional aftercare helps maintain the properties of the ceramic coating and helps minimise water spotting.
Cleaning Product Limits
Avoid cleaning agents with a pH below 3 or above 12.
Important Product Handling
Ceramic Body Cb0.01 reacts with humidity. Therefore, crystals may form around the bottle opening after you open the product.
Before dispensing the coating, inspect the bottle opening and remove any crystals with a clean cloth. Crystals that transfer onto the Application Towel may scratch the paint surface.
After opening the bottle, store it for a maximum of approximately 6 months. Always check the bottle for crystallisation before each use.
Finally, before use, read all hazard warnings on the container or outer packaging and take the appropriate protective measures.




















Reviews
There are no reviews yet.